linux user group brescia

ho attaccato alla mia slackuerina 9 appena uscita un modemusb isdn e il
dmesg mi ritorna questo :
Linux version 2.4.20 (root a midas) (gcc version 3.2.2) #2 Mon Mar 17 
.......




......usb-ohci.c: USB OHCI at membase 0xc688e000, IRQ 11
usb-ohci.c: usb-00:01.3, Silicon Integrated Systems [SiS] 7001 (#2)
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 11 for device 00:01.2
PCI: Sharing IRQ 11 with 00:01.3
usb-ohci.c: USB OHCI at membase 0xc6890000, IRQ 11
usb-ohci.c: usb-00:01.2, Silicon Integrated Systems [SiS] 7001
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 3 ports detected
sis900.c: v1.08.06 9/24/2002
PCI: Found IRQ 9 for device 00:01.1
eth0: SiS 900 Internal MII PHY transceiver found at address 1.
eth0: Using transceiver found at address 1 as default
hub.c: new USB device 00:01.2-1, assigned address 2
usb.c: USB device 2 (vend/prod 0x483/0x481d) is not claimed by any active
driver. eth0: SiS 900 PCI Fast Ethernet at 0xd000, IRQ 9,
00:a0:cc:c0:99:b7. usb-uhci.c: $Revision: 1.275 $ time 15:38:38 Mar 11
2003 usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
uhci.c: USB Universal Host Controller Interface driver v1.1
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
CSLIP: code copyright 1989 Regents of the University of California
ISDN subsystem Rev: 1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1/1.1.4.1 loaded
HiSax: Linux Driver for passive ISDN cards
HiSax: Version 3.5 (module)
HiSax: Layer1 Revision 1.1.4.1
HiSax: Layer2 Revision 1.1.4.1
HiSax: TeiMgr Revision 1.1.4.1
HiSax: Layer3 Revision 1.1.4.1
HiSax: LinkLayer Revision 1.1.4.1
HiSax: Approval certification valid
HiSax: Approved with ELSA Microlink PCI cards
HiSax: Approved with Eicon Technology Diva 2.01 PCI cards
HiSax: Approved with Sedlbauer Speedfax + cards
HiSax: Approved with HFC-S PCI A based cards
hiax_st5481: ST5481 USB ISDN driver v0.1.0
usb.c: registered new driver st5481_usb
st541: found adapter VendorId 0483, ProductId 481d, LEDs 2
HiSax: Card 1 Protocol EDSS1 Id=st5481_usb0 (0)
HiSax: DSS1 Rev. 1.1.4.1
HiSax: 2 channels added
HiSax: MAX_WAITING_CALLS added
eth0: Media Link On 100mbps half-duplex 
parport0: PC-style at 0x378 [PCSPP,TRISTATE]
lp0: using parport0 (polling).

Sembra che venga riconosciuto il modem, ma io che non ho mai usato ne usb
ne isdn sotto linuzzo ,ora come faccio a provare a fare una chiamata ?
Credo che mi servino le isdn4k-linux ma dopo averle installate come le uso
? 
Presumo che non posso usare minicom ....AIUTO :-)))
Ciao Guido